ASTM F2054 PDF

13 Nov Hold variables constant. Per ASTM F “If correlations between pieces of test equipment are to be made it is important that all. ASTM Standards. ASTM F ASTM F – Standard Test Method for Burst Testing of Flexible Package Seals Using Internal Air Pressurization Within. ASTM F Standard Test Method for Burst Testing of Flexible Package Seals Using Internal Air Pressurization Within Restraining Plates.

Author: Kanris Marisar
Country: Paraguay
Language: English (Spanish)
Genre: Music
Published (Last): 26 October 2015
Pages: 288
PDF File Size: 6.54 Mb
ePub File Size: 4.59 Mb
ISBN: 293-5-21887-472-5
Downloads: 35388
Price: Free* [*Free Regsitration Required]
Uploader: Danos

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Particular caution is advised where users of this procedure may be required to design and fabricate restraining plate fixtures.

Active v2054 current version of standard. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. In particular it is intended as applicable to packages with seals that have a peelable seal feature peeled open by end user to remove contents of package.

This test method should be combined with other methods of evaluating overall package integrity, uniformity of the package seal, or opening functionality, if so required. Under Test Methods F the stresses are not distributed uniformly to all areas of the package seal. This standard does not purport to address all of the safety concerns, if any, associated with its use.

In particular it is intended as applicable to packages with seals that have a peelable seal feature peeled open by end user to remove contents of package. See Appendix X2 for further information.

Link to Active This link will always route to the current Active version of the standard. By placing the package within restraining plates during pressurization, the dimensional stability of the package is maintained in a manner that results in stresses applied more uniformly along the perimeter of the package, where seals are normally placed.

  ISO 7816-7 PDF

Product List | RDM Test Equipment | Assured Quality Testing Solutions

This test method provides an indicator of the burst strength of a package, where the burst will normally occur in one or more areas of the seal. Under unrestrained conditions the stress on the package is highest at the middle of the pouch where it inflates f2504 the packages maximum diameter; therefore, Test Methods F may not reliably detect the weakest area of the seal.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Typical parameters can include, but are not limited to the package size, material, type and configuration of seal, rate of air flow into the package, pressure detection sensing mechanism and sensitivity machine response to pressure dropposition of test article, rigidity of restraining plates, and distance between restraining plates.

See Appendix X4 for information. An indicator of the minimum burst strength may be of importance to the package manufacturer and end user in ensuring adequate package integrity. Under Test Methods F the stresses are astk distributed uniformly to all areas of the package seal.

ASTM F2054

See Appendix X4 for information. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

By placing the package within restraining plates during pressurization, the dimensional stability of the package is maintained in a manner that results in stresses applied more uniformly along the perimeter of the package, atsm seals are normally placed.

  DIANNE ROBBINS TELOS PDF

This test method cannot provide a measure of package seal uniformity. Test Methods F describes methods of burst testing that do not include the use of restraining plates and are suitable to determine a packages general ability to withstand pressurization stresses. This allows the test to have a higher probability of detecting the weakest area of the seal and provide a measurement of the pressure required to “burst” open the package.

Under unrestrained conditions the stress on the package is highest at the middle of the pouch where it inflates to the packages maximum diameter; therefore, Test Methods F may not reliably detect the weakest area of the seal.

Reference Appendix X3 for further information regarding calculation of stress factors and structural design considerations.

ASTM International – Standard References for ASTM F / FM – 13

Reference Appendix X3 for further information regarding calculation of stress factors and structural design considerations. This test method also cannot provide an evaluation of overall package integrity or the burst strength of areas of the package that contact the surface of the restraining plates used.

Particular caution is advised where users of this procedure may be required to design and fabricate restraining plate fixtures. Link to Active This link will always route to the current Active version of the standard.

Test Methods F describes f2045 of burst testing that do not include the use of restraining atm and are suitable to determine a packages general ability to withstand pressurization stresses. Historical Version s – view previous versions of standard. Pressure differentials may occur during such processes as sterilization and transportation.