and wiring for Japanese specification FX1N PLC main units. This manual covers basic hardware details for the FX1N Series Programmable Logic Controller. FX1N Hardware Manual – 三菱可编程控制器FX1N型PLC硬件手册. User’s Manual. (Data Communication). FX1S/FX1N/FX2N(C)/FX3U. Interface Modules. INDUSTRIAL AUTOMATION. MITSUBISHI ELECTRIC. MITSUBISHI.
|Published (Last):||6 February 2004|
|PDF File Size:||14.71 Mb|
|ePub File Size:||15.14 Mb|
|Price:||Free* [*Free Regsitration Required]|
For greater detail, specifications and wiring examples for each optional unit, please see the relevant product manuals. The enclosure should be selected and installed in accordance to the local and national standards.
Remove base unit top cover.
Mitsubishi FX1N-24MT-ESS/UL Manuals
All layouts are diagrammatic and are only intended to aid the creation of wiring diagrams. Always make sure the power is turned off, before installing a special function board.
Always ensure that mounted units and blocks are kept as far as possible from high-voltage cables, high-voltage equipment and power equipment. LED is lit B Check for programming error. Low voltage cables should be reliably separated or insulated with regard to high voltage cabling.
Do not remove this screw.
Mitsubishi FX1NMT-DSS Manuals
Secure top cover with M3 screw E. Terminal layouts The following selection of terminal layouts are taken from the FX1N product range. D, D M Harrware execution error ref. The rated life for an inductive AC load such as a contactor or solenoid valve isoperations at 20VA. See equation 2 for Rb calculation. Remotely from a personal computer or other programming peripheral.
FX0N series extension units do not have CE certification. Fix board to base unit using screws C. C M3 screw to secure board. It should be read and understood before attempting to install or use the unit. The capacitor backed memory will retain programs for a maximum of 10 days, and requires 30 minutes to recharge upon power up. Note all manaul are latched Remarks C0 to C15 Type: Check D for mannual scan time, units 0.
Note that the ground cable must not be connected to the same ground as the power circuits.
Mitsubishi FX1NMT-ESS/UL Manuals
D, D M ref. The operators should also be familiar with documentation which is connected with the actual operation of the completed equipment.
Owing to the very great variety in possible application of this equipment, you must satisfy yourself as to its suitability for your specific application. However Additional extension blocks can be powered from the main unit power supply 4. The definition of such a person or persons is as follows; a Any engineer who is responsible for the planning, design and construction of automatic equipment using the product associated with this manual should be of a competent nature, trained and qualified to the local and national standards required to fulfill that role.
These engineers should also be trained in the use and maintenance of the completed product. The manual has been written to be used by trained and competent personnel.
Only one board can be used at any one time, do not try to stack multiple boards. AC, World spec, CE registered.
Mitsubishi FX1N-24MT-DSS Manuals
Whenever any of the following symbols are encountered, its associated note must be read and understood. Down load a small test program into the PLC. All maintenance should be carried out in accordance with established safety practices. Each of the symbols used will now be listed with a brief description of its meaning.
Occupied points are shown in brackets for input and outputs. FX0N series extension units do not have UL certification. Plug board A into connector B. AC Wor ld spec. During this testing stage take extreme care not to touch manuap live or hazardous parts. A standard input X0 to X17 defined by the system parameters.
Verify the program to ensure it has been written to the PLC correctly. See equation 1 for Rb calculation. E C A Special function or optional equipment board.
This manual is subject to change without notice. Input circuit power supply?