ISO 7816-3 EPUB

ISO/IEC specifies the power and signal structures, and information exchange between an integrated circuit card and an interface device such as a. ISO/IEC was prepared by Joint Technical Committee ISO/IEC JTC 1, Information technology, Subcommittee SC 17, Cards and personal identification. 15 Dec PDF disclaimer. This PDF file may contain embedded typefaces. In accordance with Adobe’s licensing policy, this file may be printed or viewed.

Author: Shaktihn Fetaxe
Country: Azerbaijan
Language: English (Spanish)
Genre: Life
Published (Last): 26 June 2012
Pages: 34
PDF File Size: 19.87 Mb
ePub File Size: 15.37 Mb
ISBN: 424-6-41003-686-1
Downloads: 42383
Price: Free* [*Free Regsitration Required]
Uploader: Katilar

When the ICC implements iso 7816-3 PTS request message correctly it replies by echoing the same request as the response message. Parity is correct when the number of ONES is even in the sequence from iso 7816-3 to 7816.

This contact is used as input reception mode or output transmission 78163- for data exchange. Next data iso 7816-3 is transferred subsequently. The format of the TS character is shown in figure This results in an implicit selection of the protocol and the communication parameters. This is effectively a special command iso 7816-3 from the interface device to the ICC after the answer to reset.

T0 T1 T2 IR: Historical characters max,15 TCK: The command header consists iso 7816-3 the following 5 bytes: The following five values are defined: The actual frequency, delivered by the interface device on CLK, is designated either by fi the initial frequency during the answer to reset, or by fs the subsequent frequency during subsequent transmission.

These global interface bytes convey information to determine parameters which the interface device shall take iso 7816-3 account. N codes directly the extra guard time, from 0 to etu. The electrical circuits shall not be activated until the contacts are connected to the iso 7816-3 device so as iso 7816-3 avoid possible damage to any card meeting these standards. Initial character TS Structure of the subsequent characters in the Answer to Reset ————————————————————- The initial character TS is followed iso 7816-3 a variable number of subsequent characters in the following order: Check character Figure 4: The binary encoded fields are compared against tables supplied in the standard to achieve actual values for F and D as defined below.

  INVESTINDO EM SMALL CAPS PDF

Table 3 — Electrical characteristics of CLK under normal operation conditions.

ISO Introduction

If iso 7816-3 5 of the PTS1 response character is set to zero then iso 7816-3 default values of F and D will be used. In an answer to reset, the interface iso 7816-3 TC2 codes the integer value WI over eight bits b8 to b1. Created inupdated in isk, amended in Electrical characteristics of VPP under normal operation conditions. Retrieved from ” https: Protocol 781-63 T ————— The iso 7816-3 least significant bits of any interface character TDi indicate a protocol type T, specifying rules to be used to process transmission protocols.

The dialogue between the interface device and the the card shall be conducted through the consecutive operations:. Interface character [ codes N ] TDi: This allows the interface ieo to determinate the etu initially used by the card.

When parity is incorrect, from Iso 7816-3 library for chip cards. The following five values are defined:. A new concept is proposed which identifies the principle of two modes of operation: Three types of procedure bytes are specified: An active state on VPP should not only be provided and maintained when requested by the card.

  RODRIGUEZ MANZANERA CRIMINOLOGIA PDF

Iso 7816-3 priority of testing for asynchronous or synchronous cards is not defined in this standard.

Table 5 — Electrical characteristics of VCC under normal iso 7816-3 conditions. The card may optionally send a NULL procedure byte 60hex which allows further time for the processing of the command.

ISO part 3 smart card standard

State H of the clock pulses can iso 7816-3 varied between 10us and 50us t15 and state L between iao and us t If no character repetition is provided by the card, — The iso 7816-3 ignores and shall not suffer damage from the error signal coming from the interface device. There isn’t and probably won’t be a smart card related SE site.

When no TC2 appears in the answer to reset, the default value of WI is 7861-3 A command is always initiated by the interface device.

The chronological order of transmission of information 78163- shall correcpond to bit identification b1 to b32 with the least iso 7816-3 bit transmitted first. N is an extra guardtime requested by the card.

ISO/IEC 7816

Cards with contacts — Dimensions and location of the contacts”. This subject is being considered further as part of the emerging part 4 of the ISO standard. The data bits can therefore be sampled at the iso 7816-3 edge iso 7816-3 the following clock pulses.